****Watch the OURA Sidecap Install Video on project documents*****

To help you get the OURA Sidecap set accurately!

    STEP 2: Locate & Audit the Oura Display in the Electronics Department

Audit to see of the OURA Sidecap is set on the POG.
If the Oura Sidecap is already set – move on to Step 4.

Partner with a Store Contact as needed to locate the Oura Sidecap Shipment in the backroom. It shipped direct to store! It will NOT have on hands in Mydevice

Look in the BDS Channel partners holding area in the backroom. Box will have a yellow "HOLD FOR BDS" yellow tape on it. See procedure for a photo of box.

1    Were you able to locate the Oura sizing ring Sidecap fixture box in the backroom?


2    Upon ARRIVAL, take a BEFORE photo of the Oura Sidecap on the Salesfloor.
Photo Comments:


    Please make sure you are taking adequate time to locate this display if tracking shows it was delivered and work with Target store teams to locate.

Shipment WILL NOT be in RMS or SBT Holding areas in the Backroom! Look for FIXTURE in ”BDS” Holding Area.


3    Take a photo of the Sidecap Shipment Box located in the backroom.
Photo Comments:


4    Take a photo showing the BDS Channel Partners backstock area.
Photo Comments:


5    Please note the name of the Target team member who can verify the Oura Sidecap fixture is not in the backroom.


6    Take a photo of the Oura Endcap, if the Oura SIDECAP is NOT set, take an OVERVIEW photo of the Tech Department.
Photo Comments:


    Your visit is now done. A revisit will be added to try to locate the fixture again.


    Using a Zebra MyDevice, locate POG location on the salesfloor to install the OURA sidecap. Oura Sizing Ring Sidecap DPCI: 057-94-0413. NOTE: Do NOT use the DPCI to determine if the sidecap has arrived.

This installation location should be on the right side of the Oura 5 Smart Ring endcap as shown in this example photo. Even if the endcap has not been set in your store yet, you should still install the Oura sizing ring Sidecap based on the POG location for it and the future Oura endcap display.


7    Were you able to locate the POG location for where the new Oura Ring 5 Sidecap fixture will be set?


8    Take a before photo of the endcap showing the right side where the sidecap/sidekick will be installed. (BEFORE INSTALLATION)
Photo Comments:


9    Take a before photo of the actual OURA sidecap/sidekick FIXTURE BEFORE installing on the endcap.
Photo Comments:


10    Why were you unable to locate the installation location based on the DPCI and the placement of the Oura endcap display?


    You will now install the new Oura 5 static inline display fixture. Please follow the instructions carefully.
Instructions are in the procedure and printed in the sidecap box.


    STEP 3: Set the Oura Sidecap in the Electronics Department

Set the Oura Sidecap onto the RIGHT SIDE of the Oura Ring Display Fixture, using the Install Instructions on pgs 2-5 of the procedure.
Oura Sizing Ring Sidecap DPCI: 057-94-0413
Make sure the Sidecap is properly secured to the Oura Endcap.

The Oura Sidecap may arrive with brackets on the wrong side of the fixture, unscrew and flip them so the Sidecap can be set on the RIGHT.


    After the Sidecap is SET & SECURED, Use your phone to scan the QR code on the back & ACTIVATE the Display.
- Stick the QR code onto the back of the fixture & scan with your phone to activate.

AFTER scanning the QR code, you will be prompted to enter a code to activate!
DISPLAY CODE: PL5MNC


11    Were you able to successfully install the Oura sizing ring Sidecap fixture on the right side of the Oura endcap?


12    Did you scan the QR code & follow the prompts to complete the registration of Sidecap Unit?


13    Why were you unable to install the Oura sizing ring Sidecap onto the Oura Endcap AT ALL?


14    Based on your above answer, this question does not need to be answered. Please skip to the next question.

15    Based on your above answer, this question does not need to be answered. Please skip to the next question.

16    If store refused or other, please explain.


    You will now need to locate the Oura Ring 5 sizing kits to place on the Sidecap hooks. Please use a Zebra MyDevice and work with Target store teams to locate these kits in the backroom and hang from the hooks. Oura Ring 5 Sizing Kit – DPCI: 057-03-0616


    STEP 4: Zone & Stock the Oura DPCI on the Sidecap

Stock ONE Oura Sizing Ring DPCI onto the Oura Sidecap.
Oura Ring 5 Sizing Kit – DPCI: 057-03-0616

Use the “Take” function on the Target Device to pull product from the backroom.

Stock to make the POG look FULL & IMPACTFUL.


17    Were you able to locate and place the Oura Ring 5 sizing kits on the hooks on the Sidecap?


18    Why were you unable to locate and place the Oura Ring 5 sizing kits on the hooks?


19    Please explain why you could not place Oura Ring 5 sizing kits on the hooks.


20    Please take a picture showing the installed Oura sizing ring Sidecap fixture installed on the right side of the Oura electronic display fixture, if present, as well as any Oura Ring 5 sizing kits you placed on the Sidecap hooks.
Photo Comments:


    Check-out with store PML/Additional comments


21    Did you check-out with the store’s PML (Presentation Merchandising Lead) to confirm the completion of the project?


22    Based on your above answer, this question does not need to be answered. Please skip to the next question.

23    Based on your above answer, this question does not need to be answered. Please skip to the next question.

24    Based on your above answer, this question does not need to be answered. Please skip to the next question.

25    Do you have any issues or comments regarding this store visit?